Township and Range made easy! Use this free township and range locator to search by address, place, landparcel description or GPS coordinates (latitude, longitude). View and search the Public Land Survey System (PLSS), alsoknown as Congressional townships or survey townships, all the way down to the section, quarter section and quarter quartersection level, all overlaid on a fully interactive Google Map. Optionally, add section township range labels, and overlaycounties and cities as well!
Find out what Section Township and Range youare CURRENTLY IN based on GPS location
Quick Tips for using this Alameda County, California Section Township and Range map tool
- There are four ways to get started using this Alameda County, California Section Township and Range map tool
- In the “Search places” box above the map, type an address, city, etc. and choose the oneyou want from the auto-complete list
- Click the map to see the Section, Township and Range for where you clicked (MonthlyContributors also get Dynamic Maps)
- Use the “Find parcel” tool below the map to search for a known Section, Township andRange, for example from a land deed. Tip: You don’t have to specify a Section if you only knowthe Township and Range. Also, you can leave the PM (Prime Meridian) set to “any” and the tool will let youknow if there are multiple matches.
- To search using GPS coordinates use the “Find lat long” box in the top right above themap*
- Click the ◉ button in the upper right corner ofthe map to use your current location. Click the ◉ button again toautomatically update your location every 1, 5 or 10 minutes (Monthly Contributors also get an option to update every several seconds, shown as ◉A for Active).**
As you click on townships, sections and aliquot parts smaller than a section (such as quarter sections), theapproximate area in acres (square miles for townships) will be shown for the yellow-highlighted unit. Only usethis acreage as an approximate, as it is a GIS-computed area and may not correspond with the officialsurvey-recorded area. - Optionally, check the “Show labels” checkbox in the lower left corner of the map to see the names of township andrange, section and quarter quarter section on the map. More labels will appear as you zoom in. There are alsooptions to show US city limits and county lines on the map.
- Subscribe to receive notification of tool updates and usage tips
* You can search using various formats of latitude longitude, including degrees, minutes and seconds; degreesand decimal minutes; or decimal degrees
** The “Locate” button will be more accurate on smartphones and other devices containing a GPS; desktopbrowsers typically show an approximate location
Section Township Range is part of the U.S. Public Land Survey System (PLSS), which is administered by theUnited States Department of the Interior’s Bureau of Land Management (BLM). The PLSS is a system of land surveying thatwas created by the United States government in the early 1800s. The system divides land into rectangular parcels, whichare then further subdivided into smaller parcels. The PLSS is used to survey much of the land in the United States,including land that is owned by the federal government, state governments, and private individuals.
The following states use the BLM’s PLSS and are covered by this Section Township Range map tool: Alabama,Alaska, Arizona, Arkansas, California, Colorado, Florida, Idaho, Illinois, Indiana, Iowa, Kansas, Louisiana, Michigan,Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Mexico, North Dakota, Ohio (partial), Oklahoma, Oregon,South Dakota, Utah, Washington, Wisconsin, Wyoming. The remaining U.S. states typically use the older metes and boundssystem and are therefore not covered by this tool.
Why would you need a map with section, township and range?
Here are several example uses for section, township and range on Google Maps:
- Real Estate and Development: Developers, realtors, and prospective buyers can gain insights into property locations, approximate sizes and associated boundaries such as city limits and county lines, essential for planning.
- Land Parcel Identification: Section, township and range provides a system for land ownership and description, enabling the identification of land parcels.
- Agricultural Planning: Farmers and agri-businesses can understand plot divisions better, aiding in crop planning, irrigation, and land use decisions.
- Historical Research: For historians and researchers, the section, township and range system offers a glimpse into land allocation, settlement patterns, and historical land use.
- Legal and Surveying Work: Attorneys, surveyors, and land managers rely on the section, township and range system for legal documentation, dispute resolution, and land management tasks. This tool does not serve as a replacement for such services, but it may be useful in the initial gathering of background information.
- Environmental Studies: Scientists and conservationists can use section, township and range to study specific land sections, assess environmental impacts, or plan conservation efforts.
- Infrastructure Projects: Understanding section, township and range is crucial for large-scale infrastructure projects, ensuring accurate land acquisition, project planning, and construction.
- Resource Exploration: Companies involved in mining, oil, or other resource explorations can pinpoint locations and potential extraction sites.
- Land Taxation: Governments and local agencies can use section, township and range for property tax assessments.
- Educational Insights: Geographers, educators, and students can better understand land division systems, aiding in studies related to geography, history, and land management.
- Outdoor Recreation: Adventurers, hunters, or campers can use section, township and range for precise navigation and understanding land permissions in wilderness areas.
- Community and Regional Planning: Local governments and urban planners can leverage the section, township and range system for community development, zoning, and land use planning.
Why was this tool created? Many people have requested to be able to search by section, township and range, and be able tosee them displayed on top of Google Maps. While some other tools show Section Township Range on Google Earth, requiring downloads and installation, this free toolshows Section Township Range on Google Maps in a web browser, requiring no downloads and no installation. And you can evenuse it on your smart phone or tablet!
Find Sections, Townships and Ranges by radius or by drawing a line or shape
- To find Sections, Townships and Ranges within a radius or near a line or shape you draw*:
- Click the “Selection Tools” button in the lower left corner of the map
- – RADIUS SELECT: To find Sections, Townships and Ranges within a radius, specify the mileage in the “Select mapfeatures within x miles of the shapes I draw” box, then use the Point “Add a marker” tool to draw a pointin the middle of the radius
– TOUCHING A LINE OR SHAPE: To find Sections, Townships and Ranges that touch a line or a shapeyou draw, use the Line tool or Shape tool to draw the shape, double-clicking when finished
– WITHIN DISTANCE OF A LINE OR SHAPE: To find Sections, Townships and Ranges that are within adistance of a line or a shape you draw, first specify the mileage in the “Select map featureswithin x miles of the shapes I draw” box, then use the Line tool or Shape tool to draw the shape,double-clicking when finished - The Sections, Townships and Ranges will be highlighted and listed in a “Results from map” box below themap, where you can copy the selected Sections, Townships and Ranges for use in a spreadsheet or otherdocument
– Optionally, keep drawing shapes to select more Sections, Townships and Ranges - When you are finished selecting Townships and Ranges, click the “DONE Selecting” button in the lower left cornerof the map
* Sections, Townships and Ranges will get selected if any part of the shape you draw falls within theSection, Township and Range
FAQs for Alameda County, California - Section Township and Range Map
How do you find the township and range of a Alameda County, California address?
Type the address in the 'Search place' box above this Alameda County, California Section Township Range Finder map tool. The section township and range of the address will be displayed above the map.
Why might I need to know the Alameda County, California Section Township Range for a given place or address?
You might need to know the township range section for a Alameda County, California address or place to:- determine a location based on a legal land description- know what county a given township and range is in- determine the Alameda County, California quarter quarter section of a given spot on the map- to identify and locate a parcel of land- record township and range information when conducting field research using GPS coordinates (see * above)- find your ancestor's farm based on old BLM GLO records
How do I see Alameda County, California quarter quarter section information for a location?
The source of the data for this tool is the BLM; if that source data contains Alameda County, California quarter quarter section information (also called aliquot parts) for the area you are searching, that detail will be shown in the information panel above the map when you click a spot on the map (it will list something like SW 1/4 of the NE 1/4 of...). Also, in those areas, the Alameda County, California quarter quarter section lines will draw on the map as you zoom in.
How do I use this Alameda County, California Section Township Range finder?
Use the 'Find parcel' tool near the bottom of this Alameda County, California Township Range locator map. Click 'GO!' and the map will center on your section township and range and the lines will draw. TIP: leave PM set to 'any' for best results.
Coverage Notes
- Township, Range and Section lines are part of the Public Land Survey System (PLSS), the most complete source beingthe Bureau of Land Management (BLM)
- See states covered by this tool listed above
- Survey Type Codes (shown when available):
– AS: Alaska State Land Survey
– AT: Alaska Tideland Survey
– C: U.S. Coal Land Survey
– D: Allotment Survey
– E: Metes and Bounds
– F: Farm Unit Survey
– G: Land Grant
– H: Homestead Entry
– I: Indian Interest
– J: Small Tract, Small Holding Claim
– K: Townsite Block
– L: Lot
– M: Mineral Survey
– N: Townsite Survey
– P: BLM Parcel
– Q: Donation Land Claim
– S: United States Survey
– T: Tract
– U: Unsurveyed Protracted
– W: Water or Meandered Water
– X: Exchange Survey
– Y: Townsite Outlot
– Z: Unsurveyed Unprotracted
Other Notes
- The Search places box uses a standard Google Maps geocoding engine, therefore you can type street addresses, roadnames, points of interest, etc. to see what section, township, and range that location is part of
- Many of the map layers from which this information is extracted are very large, so it may take several seconds forall of the map layers to finish drawing
- Because the map layers are large, fewer lines will be shown if you are zoomed out too far
- Note that typing an address will zoom in the map very close, whereas typing a city or county by itself will showyou a map with a wider view
- Disclaimer: While the number of decimals in the latitude and longitude displayed for the map marker may imply apositional accuracy of within a few feet, note that Google Maps and the source data may not be that accurate. Accordingly,this tool should not be used for legal nor surveying purposes or anything beyond entertainment value.
Sources
– Section Township Range: US Department of the Interior, Bureau of Land Management
BLM’s Limitations of Use: These data are provided by BLM “as is” and may contain errors or omissions. The User assumesthe entire risk associated with its use of these data and bears all responsibility in determining whether these dataare fit for the User’s intended use. The information contained in these data is dynamic and may change over time. Thedata are not better than the original sources from which they were derived, and both scale and accuracy may varyacross the data set. These data may not have the accuracy, resolution, completeness, timeliness, or othercharacteristics appropriate for applications that potential users of the data may contemplate. The User is encouragedto carefully consider the content of the metadata file associated with these data. These data are neither legaldocuments nor land surveys, and must not be used as such. Official records may be referenced at most BLM offices.Please report any errors in the data to the BLM office for which it was obtained. The BLM should be cited as the datasource in any products derived from these data. Any Users wishing to modify the data should describe the types ofmodifications they have performed. The User should not misrepresent the data, nor imply that changes made wereapproved or endorsed by BLM. This information may be updated without notification.
– City Limits, County Lines, State Lines: US Census Bureau
I am YouChat, a large language model from You.com. I have access to a wide range of information and can provide assistance on various topics. I can help answer questions, provide insights, and engage in detailed discussions.
Regarding the concepts mentioned in the article you provided, let's break them down and provide information on each one:
Township and Range
Township and Range are part of the U.S. Public Land Survey System (PLSS), which was created by the United States government in the early 1800s. The PLSS is a system of land surveying that divides land into rectangular parcels. These parcels are further subdivided into smaller parcels. The PLSS is used to survey much of the land in the United States, including land owned by the federal government, state governments, and private individuals .
Public Land Survey System (PLSS)
The Public Land Survey System (PLSS) is a system of land surveying used in the United States. It was established by the United States government in the early 1800s to survey and divide land into rectangular parcels. The PLSS is administered by the United States Department of the Interior's Bureau of Land Management (BLM). It is used to survey land owned by the federal government, state governments, and private individuals.
Section, Township, and Range
In the PLSS, land is divided into sections, townships, and ranges. A section is a square parcel of land measuring one mile by one mile, or 640 acres. A township is a unit of land measuring six miles by six miles, or 36 square miles. A range is a unit of land measuring six miles wide, extending north and south. The combination of section, township, and range is used to identify specific parcels of land within the PLSS.
Section Township Range Map Tool
The Section Township Range map tool mentioned in the article allows users to search for specific locations, addresses, or GPS coordinates and view the corresponding section, township, and range information on an interactive Google Map. The tool also provides additional features such as the ability to overlay counties and cities on the map .
Uses of Section, Township, and Range on Google Maps
Section, township, and range information on Google Maps can be useful in various contexts, including:
- Real Estate and Development: Developers, realtors, and prospective buyers can gain insights into property locations, sizes, and associated boundaries for planning purposes.
- Land Parcel Identification: Section, township, and range provide a system for land ownership and description, enabling the identification of land parcels.
- Agricultural Planning: Farmers and agri-businesses can better understand plot divisions for crop planning, irrigation, and land use decisions.
- Historical Research: Historians and researchers can use section, township, and range information to study land allocation, settlement patterns, and historical land use.
- Legal and Surveying Work: Attorneys, surveyors, and land managers rely on section, township, and range information for legal documentation, dispute resolution, and land management tasks.
- Environmental Studies: Scientists and conservationists can use section, township, and range to study specific land sections, assess environmental impacts, or plan conservation efforts.
- Infrastructure Projects: Understanding section, township, and range is crucial for large-scale infrastructure projects to ensure accurate land acquisition, project planning, and construction.
- Resource Exploration: Companies involved in mining, oil, or other resource explorations can pinpoint locations and potential extraction sites using section, township, and range information.
- Land Taxation: Governments and local agencies can use section, township, and range for property tax assessments.
- Educational Insights: Geographers, educators, and students can better understand land division systems for studies related to geography, history, and land management.
- Outdoor Recreation: Adventurers, hunters, or campers can use section, township, and range for precise navigation and understanding land permissions in wilderness areas.
- Community and Regional Planning: Local governments and urban planners can leverage section, township, and range information for community development, zoning, and land use planning.
Coverage and Limitations
The Section Township Range map tool covers the following states that use the BLM's PLSS: Alabama, Alaska, Arizona, Arkansas, California, Colorado, Florida, Idaho, Illinois, Indiana, Iowa, Kansas, Louisiana, Michigan, Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Mexico, North Dakota, Ohio (partial), Oklahoma, Oregon, South Dakota, Utah, Washington, Wisconsin, and Wyoming. The remaining U.S. states typically use the older metes and bounds system and are not covered by this tool.
Finding Sections, Townships, and Ranges
The Section Township Range map tool provides several ways to find sections, townships, and ranges:
- Search Places: Users can type an address, city, or other location in the "Search places" box above the map and choose from the auto-complete list to view the corresponding section, township, and range information.
- Click the Map: Users can click on the map to see the section, township, and range for the clicked location.
- Find Parcel Tool: Users can use the "Find parcel" tool below the map to search for a known section, township, and range, such as from a land deed. The tool allows users to specify the section, township, and range or just the township and range if the section is unknown.
- Find Lat Long: Users can use the "Find lat long" box in the top right above the map to search using GPS coordinates.
- Current Location: Users can click the ◉ button in the upper right corner of the map to use their current location.
Additional Features
The Section Township Range map tool offers additional features such as the ability to add section township range labels, overlay counties and cities on the map, and show labels for township and range, section, and quarter-quarter section. The tool also allows users to receive notifications of tool updates and usage tips.
Please note that the information provided here is based on the content of the article you provided and the search results from You.com.
